In this view, the bars are adjacent to the left side of the PRI. While the display on your 325P2 would look different, it would still have the signal strength bars in the upper right corner. This is a screenshot from my 536HP, as it shows in ProScan. Those would 'come and go' as the scanner runs through the individual sites. When scanning, but not hearing anything, are you seeing the signal strength bars in the upper right corner of the display? Just to clarify, you are not seeing a "Nothing to Scan" message on the display, just not receiving anything. While a handful of the talkgroups indicate as encrypted, there are more than enough non-encrypted TGIDs that you should hear something. Looking at your file, I don't see anything missing or locked out, preventing reception. The last item, "resume scanning" tells the scanner to start back up scanning, without waiting for you to manually tell the scanner to resume. The 'Send Global lockouts" and "Quick Key status" tells FreeSCAN to send anything you have labeled as locked out in the scanner settings (like the Broadcast screen", and also to activate any quick keys that you set as active in your file. If, for example, you had a number of other systems programmed, and were using the same basic file on an analog scanner, like the BCT15X, FreeSCAN would not send any digital systems to that scanner, because it cannot monitor those. The "Don't send digital channels." selection tells FreeSCAN not to send digital frequencies & trunked systems to a non-digital scanner. Here, you can specify display options, weather SAME codes, and other items listed on the tabs of that page. The item labeled as "Send custom radio settings" tells FreeSCAN to load the details you can specify on Set Scanner Options menu (select that from the drop-down Scanner menu on FreeSCAN's main screen). I always use the 'erase all systems' options, so that I don't accidentally add the same system more than once. I never use this, because if I was loading other systems, I might be duplicating what had been uploaded to the scanner previously, leaving you with duplicates. "Add only, do not overwrite" would add any system you selected to upload to what was already in the scanner. IF you already had the Bergen system loaded, but wanted to only replace that one, but not any other systems loaded in the scanner, you could use the "Replace any existing system with the same name, and add remaining", that would load Bergen, overwriting what was already there (if any previously loaded), then it would add any other systems that you also selected to load. The "Erase all systems." clears any older programming from the scanner, then loads only the system you have selected. You select the system to load on the left side, which in your case is Bergen County, You're talking about the normal upload choices that FreeSCAN shows: I have viewed dozens of YouTube videos but most were for conventional programming. Hopefully some one can see a problem in my workflow and get me on track. Now in the upload window On freescan I see a problem with upload status. After it uploads I see my scanning, scanning but receive nothing. The first 3 top choices I choose erase all systems and settings. The last 5 are checking and I leave them checked. I see my project Bergen County with a checked box. I then go to up load my project to my scanner. The next 3 I’m not sure what to do being they have two choices. In the nest window I have a folder on the upper left which says: Next on the right side of this window I uncheck all 20 choices and re-check one (interboro Police) and select import. Go over to available systems: in the drop down window I select Bergen County (APCO P25) I go to file, import, over to radio reference Trunked and select. I have a feeling this could be my problem. Maybe some one can look over my work flow loading sites onto my Uniden BCD325p2 and tell me what I might be doing wrong. Thanks guy’s for all the good information. Hopefully some one can shed some light on what’s going on here. I really don’t see any TG 1202 or TG 1204 tags and I do not see 155.4300 frequency listed. It seems to me when I load the software from radio reference in to free scan I do not see the correct TG tags or frequencies. Alpine, Demarest and Haworth are using TG 1202, Harrington Park, Norwood & Northvale using TG 1204,ĭoes anyone have any idea why I may be having a problem? Could it be I need one of Uniden’s paid software upgrade? Interboro Police - Harrington Park, Norwood, Northvale, Closter, and Haworth Police Departments all have switched to using the Bergen County trunked radio system. Northern Valley (Interboro) Police Bergen County Project 25 Phase ll here’s the information of what I’m dealing with. I been trying to program the scanner for 3 day’s without success. I’m using free scan and radio reference for programming. I purchased my first digital scanner last week.
0 Comments
Leave a Reply. |